Everlube Lubri bond 220干膜润滑涂层

Lubri-Bond 220 干膜润滑涂层is an air drying, MoS2 based solid film lubricant with an epoxy binder system. This coating provides
good corrosion resistance and performs best in higher load carrying applications. It is ideal for applications that do
not require a thermally cured coating. Lubri-Bond 220 is approved/qualified to many aerospace and industrial
specification;

When requesting
pricing or ordering of product, listing of the specification and revision is required to assure product certification
compliance.
Features / Benefits
 Good corrosion resistance
 Fair chemical resistance
 Suitable for field applications
 Ideal for higher load carrying applications
Markets Typical Applications
 Aerospace/Defense
 Mechanical Components
 Industrial Machinery & Equipment
 Fabricated Metal Parts
 Tooling, brackets and wear plates
 Guide and sliding rails
 Seals, clamps, and couplings
 Bearings, gears, splines and cams
Physical Properties
Lubricating Solids: MoS2
Binder: Epoxy
Color and Appearance:* Gray/black matte finish
Carrier: Solvent based
Solids (by weight):* 23.6 to 27.6%
Density:* 8.3 ± 0.5 lb/gal (995 ± 60 grams/liter)
Flash Point: 45°F (7°C)
Volatile Organic Compound: 737 grams/liter (6.15 lb/gal)
Theoretical Coverage:1 286 ft²/gal @ 0.5 mils (7 m²/liter @ 12.7 microns)
Alternative or Repair Coatings: Thermally cured and water-based equivalents for Lubri-Bond
220 are Everlube 620C or Ecoalube 642 and Everlube 9002,
respectively.
Processing Information2
 
Dry Film Thickness 0.3 to 0.6 mils (8 to 15 microns)
Dilution/Cleanup Solvent: MEK
Dilution Ratio for Spray: 0 to 1:1 (Product to Solvent by volume) adjust as needed
Cure Cycle: 24 hr. @ 77°F +/- 10°F
Suggested Pretreatment: Grit blast and/or phosphate
Suggested application Methods: Dip spin, spray
 
For additional information, please see Processing Bulleting #3000-A
 
(Continued)
 
 
Technical Data (Spec Qualified)
Lubri-Bond® 220
 Air Dry, MoS2 Solid Film Lubricant
This document is for technical reference only and is not intended for use in developing a specification. Specification writers should contact Technical Director of Research and
Development. The information supplied is presented in good faith and has been derived from sources believed to be reliable. Since conditions of use are beyond our control,
all risks are assumed by the user.
 
Lubri-Bond® 220, Air Dry, MoS2 Solid Film Lubricant
Page 2 of 2
Typical Functional Properties
 ASTM Test Method Value
Corrosion Resistance
 Test Panel ASTM B-117 >100 hrs. @ 5% neutral salt spray
 Test Panel Coating Method 0.8 mil on grit blasted steel panel
Abrasion Resistance ASTM D-4060 Fair
Coefficient of Friction ASTM D-2714 0.04 to 0.06
Operating Temperature Range -100°F to 250°F (-73°C to 121°C)
Load Carrying Capacity ASTM 2625, Method B >250,000 psi
Wear Life ASTM 2625, Method A >60 minutes
Film Adhesion* ASTM D2510, Method A Pass
Sulfurous acid salt spray* Fed-Std-791, Method 5331 Pass 4 cycles
Thermal Stability ASTM D2511 Pass
Chemical Resistance (ASTM D-2510, Method C)
Isopropyl Alcohol or Ethyl Alcohol Pass Diethanolamine Pass
Mineral Spirits or Paint Thinner Pass Hydrochloric Acid (10%) Pass
Toluene Pass Sodium Hydroxide (10%) Pass
Acetone Pass Distilled Water Pass
Skydrol 500 Pass Jet Fuels (JP-4) Pass
Hydraulic Fluids Pass Trichloroethylene Pass
Anti-Icing Fluids Pass Hydrocarbon test fluid, TT-S-735 Pass
Cleaning Compound, MIL-C-372 Pass Aviation Gasoline, MIL-G-5572 Pass
Petroleum Hydraulic Fluid, MIL-H-5606 Pass Lubricating Oil, MIL-L-22851 Pass
Lubricating Oil, MIL-L-23699 Pass Hydraulic Fluid, Non-petroleum Pass
Silicone Damping Fluid, VV-D-1078 Pass Gasoline, MIL-G-3056 Pass
Lubricating Oil, Gd. 1100, MIL-L-6082 Pass Aircraft Turbine Oil, MIL-L-7808 Pass
 
Note: Chemical resistance may vary depending on the cure cycle. N/R = Not recommended
Additional Information
Shelf Life and Storage:
One year from date of shipment, stored in a factory sealed container between the temperatures, 40F to 100F.
Coatings are thermally stable, but we do not recommend prolonged exposure outside of the specified temperature
range listed above.
Packaging: Lubri-Bond® 220 is available in Gallon, 5-Gallon Pail, Quart, Aerosol Case
Warranty:
No representation of warranty is expressed or implied and all warranties including warranties of marketability and
fitness for use are expressly disclaimed. Nothing herein shall be construed as permission or recommendation to
practice a patented invention without a license.
* These tests are performed on each production lot
1
 Based on 100% transfer efficiency at a dry film thickness of 0.0005 inch (12.5 microns).
 
Issue Date: 08/20/02, Latest Revision Date: 12/2/10